LP6016-01 / LP6016-01P – Rauscharme DC-Spannungsquelle
- Geringes Rauschen
10 μVrms oder geringer bei einer Bandweite von 10 Hz bis 20 MHz - Stabiler Spannungsausgang
±10 ppm/℃ typisch - Einstellgenauigkeit
±( 0,03 % + 250 μV ) bei einer Einstell-Auflösung von 500 µV - Hohe Genauigkeit für
- Bias-Spannung für Sensoren
- Spannungsquelle für Bauteile und Komponenten
- Externe Kontrolle mit USB, RS-232 oder LAN-Schnittstelle
- 0 bis ±16,1 V Ausgangsspannung
- 100 mA maximaler Ausgangsstrom
Videos
NF Low Noise DC Voltage Source LP6016-01/01P
NF stellt die rauscharme Gleichspannungsversorgung vor:
Low Noise DC V Source LP6016-01/01P
Dauer: ca. 2½ Minuten
Sprache: Englisch
NF Low Noise DC Voltage Source LP6016-01
NF stellt die neue Gleichspannungsversorgung mit geringem Rauschen vor:
Low Noise DC Voltage Source LP6016-01
Dauer: ca. 2 Minuten
Sprache: Englisch
Anwendungen
- Kontroll-Spannung für elektronische Bauteile und Komponenten
mit verbesserter Frequenzstabilität
- Bias-Spannung für Sensoren
mit verbessertem Rauschabstand
z.B.: - Testen von Photodioden,
(der Ausgang hängt direkt mit dem Rauschen der Versorgung zusammen,
speziell bei kleinen bis sehr kleinen Signalen)
Spezifications
| LP6016-01 | LP6016-01P | |
|---|---|---|
| Output voltage | Positive + : 0.0000 V to +16.1000 V Negative – : 0.0000 V to ‒16.1000 V | V1 : 0.0000V to +16.1000 V V2 : 0.0000V to +16.1000 V |
| Setting resolution | 0.0005 V (500 μV) | |
| Setting accuracy | ±(0.03% of | Setting value | +250 μV) Ambient temperature 23℃ ±5℃ | |
| Temperature coefficient | ±10 ppm/℃ typical | |
| Maximum current | ±100 mA ( | Output Voltage | ≥ 1V, 0 to 50℃) ±100 mA ( | Output Voltage | < 1V, 0 to 40℃) ±90 mA ( | Output Voltage | < 1V, 40 to 50℃) | 100 mA (|Output| ≥ 1V, 0 to 50℃) 100 mA (|Output| < 1V, 0 to 40℃) 90 mA (|Output| < 1V, 40 to 50℃) |
| Settling time | 100 ms (with no load) | |
| Line regulation | Within ±0.1 mV (for supply voltage ±10%) | |
| Load regulation | Within ±5 mV (load 0% reference for 0 to 100%) | |
| Ripple noise | 10 μVrms or lower typical (load 0 mA to 100 mA, bandwidth: 10 Hz to 20 MHz) | |
| Time drift | 40 ppm (typical,8 hours after warm-up) | |
| Output connector | BNC (receptacle), for positive and negative outputs each | |
Currentmonitor | ||
| Feature | Voltage output is 1 V/100 mA times the absolute value of output current. | |
| Accuracy | ±(1%+1.5 mA) (23℃ ±5℃) ±(1%+2.0 mA) (0℃ to 50℃) | |
| Output impedance | 1 kΩ | |
| Output connector | BNC (receptacle), for positive and negative current monitors each | |
Powersource | ||
| Voltage | AC 100, 120, 220 and 240 V (selector switch) ±10% (AC250 V or lower) | |
| Frequency | 50 Hz/60 Hz ±2 Hz | |
| Power consumption | 28 VA or lower | |
General Spezifications | ||
| Overvoltage category | Ⅱ | |
| USB | USB2.0 full speed, Device Class CDC | |
| RS-232 | Baud rate : 9600/19200/38400/57600bps | |
| LAN | 10 BASE-T/100BASE-TX, TCP/IP | |
| Insulation resistance | Between all power inputs and chassis : 50 MΩ or more (with DC 500 V) Between all power inputs and outputs : 50 MΩ or more (with DC 500 V) Between output GND (COM) and chassis: 10 MΩ | |
| Withstanding voltage | Between all power inputs and "outputs/chassis": AC 1500 V for 1 minute Between output GND (COM) and chassis: ±42 Vpk (DC + AC peak) | |
| Overcurrent protection | "OCP" is signed on the display when exceeding about 100 mA. Drooping characteristic (approx. 150 mA, self recovery type) | |
| Overheat protection | Output is turned off when an internal temperature exceeds threshold "OHP" is signed on the display | |
| Operating temperature/ humidity range | Temperature : 0℃ to +50℃ Humidity : 5 % to 85 %RH, Absolute humidity: 1 g/m³ to 25 g/m³ Non-condensation | |
| Storage temperature/ humidity range | Temperature : -10℃ to +60℃ Humidity : 5 % to 95 %RH, Absolute humidity: 1 g/m³ to 29 g/m³ Non-condensation | |
| Pollution degree | 2 (indoor use) | |
| Warm-up time | 60 minutes | |
| Dimensions (mm) | 215×86×330 (without protrusions) | |
| Weight | Approx. 3.5 kg (without accessories) | |
| RoHS | Directive 2011/65/EU | |
| EMC | EN 61326-1 : 2013 EN 61000-3-2 : 2014 EN 61000-3-3 : 2013 *Available soon for LP6016-01P | |
| Safety | EN 61010-1 : 2010 *Available soon for LP6016-01P | |
| Accessories | Power cord set (3 pole, 2 m), Fuse (spare), Instruction manual | |
Options
| PA-001-3089 | BNC-Binding Post Converts Adapter |
|---|---|
| PA-001-3230 | Rack Mount Kit (EIA, for 1 unit) |
| PA-001-3090 | Rack Mount Kit (EIA, for 2 units) |
| PA-001-3231 | Rack Mount Kit (JIS, for 1 unit) |
| PA-001-3091 | Rack Mount Kit (JIS, for 2 units) |
Link zu www.nfcorp.co.jp/english/…/lp_6016_01/